Front Panel Menu Reference Tables
| Note: | Default values are shown in bold. |
Audio Settings
| Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|
| Audio | Headset | Headset Limit | 8 to -12 dB/Off Default = 0 dB |
| Headset detect | Enabled/Disabled | ||
| HS Mic Type | Electret/Dynamic | ||
| Sidetone Gain | 8 to -15 dB Default = -12 | ||
| Sidetone Control | Tracking/Non-Tracking/Disabled |
Host Settings
| Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|
| Host Settings | Host name | Edit | Press controller 4 to open a touchscreen keyboard. |
| Display | Screen Brightness | High/Medium/Low/Very Low | |
| Screen Dimming | 1 to 15 minutes Default = 2 minutes | ||
| Touchscreen sensitivity | Low, Medium, High |
2 W Audio (A/B) (C/D)
| Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|
| 2W Audio (A / B) | Interface | Power detected | Yes/No |
| Power | Enabled/Disabled | ||
| Mode | Clear-Com/RTS | ||
| 2W A | Nulling | The nulling function is only available if power is detected. | |
| 2W B | Nulling | as above | |
| Audio (B / C) | Same as Audio (A / B) | ||
Discovery
| Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|
| Discovery | Discover FSII IP TCVR | Discovered FSII IP TCVRs | Register/Unregister |
| Discover FSE TCVR | Discovered FSE TCVRs | Register/Unregister |
Transceiver
| Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|
| Transceiver | TCVR 1 ... XX View configured transceivers. Max:
| Version | |
| Label | |||
| Cable Comp (E1 only) | 0 - 69 m, 70 - 139 m, 140 - 209 m, 210 - 279 m, 280 - 349 m, ... (increments of 70 m) up to 1540 - 1609 m |
Networking
| Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|
| Networking | Management | LAN Status | Up/Down |
| LAN Port | LAN Ports 1 - 4 | ||
| DHCP | Enabled/Disabled | ||
| IP Address | |||
| Subnet mask | |||
| MAC | |||
| AES67 (only visible if AES67 has been configured to its own LAN) | LAN Status | Up/Down | |
| Dante (only visible if Dante has been configured in the CCM) | |||
| LAN Port | By default management is configured to LAN 1. This can be changed in the CCM. AES67 is configured to LAN 2. | ||
| DHCP | Enabled/Disabled | ||
| IP Address | |||
| Subnet mask | |||
| MAC | MAC address |
Administration
| Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|
| Administration | Beltpacks | Over The Air | Start OTA |
| BP Role List Sorting | Sort by Role Number/Alphabetical | ||
| Battery Type | Alkaline/NiMh (for use when not using the supplied Li-ion type batteries) | ||
| Software | Current | View current version | |
| Update | Use this to update the Base Station using a USB stick. | ||
| Reset | Reboot | Press rotary 4 to reboot now | |
| Reset to Default | Reset Base. When you reset the Base here, as well as system setup details (channels and roles), network details (IP addresses) are also reset. This is not the case when resetting the Base in the CCM. After resetting you must Add transceivers again. | ||
| Reset CCM Password | Press rotary 4 to reset CCM password to the default setting. | ||
| Support Info | Generate | Insert USB | |
| Settings | Save Restore | Insert USB | |
| CCM Access | Username Default password | ||
| Hardware | Hw Info Hw Version BOM number PCB number Serial number Product number |